Reviews of DV8 Offroad Exterior products have an average rating of 4.3 out of 5. So you will install these alligator clips and likely, it won't grab enough to get a power and ground for the turn signal to work. Just input the info and the site will let you know if what you are looking at will fit or is compatible with your specific Jeep...Love It!!! Next up, we're gonna tighten down our last three bolts. We want to start at the back because DV8 recommends starting here and just putting our hardware in loosely because we will need to finagle it a little bit. So we've grabbed our rivnut and we have a rivnut tool.

We can go ahead and take our trim removal tool and get behind it and pop it out. And you will also likely need to take some off the other side, so we're just gonna cut along the line of our fender and then make a straight cut as straight as we can. These flares will give your Jeep more maneuverability as well as durability when you're off-roading. So long as you're using even force, you should be fine. Note: Unfortunately not all products ExtremeTerrain sells can be shipped to Canada. I thought that it was very nice to see free shipping offered for my offer. Application. The fenders look great once installed but ZERO instructions and only enough nurserts to install the front fenders while the rear fenders are supposed to be bolted on with nuts, which isn’t how the wrangler version of these fenders work. However, I did wanna leave it in here just in case the truck ever needs to be returned to stock. 6400 Sycamore Canyon Blvd., Ste. So long as you're using even force, you should be fine. If it blinks, it is a turn signal. Some of the adhesive is going to be over the holes that we wanna use to put this on our truck, so you might wanna go back over it with a razor knife or a set of scissors later.Okay. That's gonna be your turn signal. Next up, we're gonna do the same thing to this part of the harness.All right, so we've peeled back our harness a little bit for our turn signal and as you can see, this gauge wiring is incredibly small. I recommend going a little at a time and we're gonna match it up with the bolt holes and the curve of the fender. You want to pull back this to expose as much of these wires as possible so that we can have enough room to tap into them.All right, so we peel back this wiring harness to expose as much of these loose wires as possible so we have enough room to cut them. Okay, so we grabbed our front fender and we're gonna put our light and our weatherstripping in it. That means there are no additional fees to pay when your package arrives! And if you're going to do this method, you wanna make sure the connectors you choose are heat shrinkable because they do make some that are not.Now, our final step with this is that you might want to put some electrical tape on here and just tuck this harness up a little more neatly and then you can use the factory location that this clip went to sort of finish tucking this up. Sitemap As long as you're only putting the bolts in, it's a little bit just enough to hold the fender on and then we will tighten them down later on. This shopping feature will continue to load items when the Enter key is pressed. Additionally, the front fenders have integrated turn lights that plug into the factory harness, improving the Jeep’s lighting capabilities as a result. If you don't have one of these, I recommend borrowing one. Now that we have our fender prepped and ready to go on our Jeep, we just wanna line it up to the holes to know which ones that we want to put a rivnut into. CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Moving on to this hole, we can just check to make sure it corresponded with our fender and we can put our rivnut in. The following are a few examples of items that can not be shipped to Canada: Products that ship directly from the manufacturer, products that require freight shipping, gift certificates or unmounted tires. We wanna make sure we do this right cause this is really only a one-shot type of wiring. And just twist it in with our turn signal power wire. They really should include nurserts for all 48 holes, not just 20 of them.